[ 0.000000] Linux version 3.8.2 (bastian@gcc20) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #3 Sun Mar 10 20:33:12 CET 2013 [ 0.000000] CPU revision is: 00029008 (Broadcom BMIPS3300) [ 0.000000] bcm47xx: using ssb bus [ 0.000000] ssb: Found chip with id 0x5352, rev 0x00 and package 0x02 [ 0.000000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0E, vendor 0x4243) [ 0.000000] ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x09, vendor 0x4243) [ 0.000000] ssb: Core 2 found: MIPS 3302 (cc 0x816, rev 0x06, vendor 0x4243) [ 0.000000] ssb: Core 3 found: USB 1.1 Host (cc 0x817, rev 0x02, vendor 0x4243) [ 0.000000] ssb: Core 4 found: MEMC SDRAM (cc 0x80F, rev 0x01, vendor 0x4243) [ 0.000000] ssb: Core 5 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243) [ 0.000000] ssb: Core 6 found: Roboswitch (cc 0x81C, rev 0x02, vendor 0x4243) [ 0.000000] ssb: chipcommon status is 0x0 [ 0.000000] ssb: Initializing MIPS core... [ 0.000000] ssb: set_irq: core 0x0806, irq 4 => 4 [ 0.000000] ssb: set_irq: core 0x0816, irq 5 => 2 [ 0.000000] ssb: set_irq: core 0x0812, irq 2 => 5 [ 0.000000] ssb: after irq reconfiguration [ 0.000000] ssb: core 0x0800, irq : 2(S) 3* 4 5 6 D I [ 0.000000] ssb: core 0x0806, irq : 2(S) 3 4* 5 6 D I [ 0.000000] ssb: core 0x0816, irq : 2(S)* 3 4 5 6 D I [ 0.000000] ssb: core 0x0817, irq : 2(S) 3 4 5 6* D I [ 0.000000] ssb: core 0x080f, irq : 2(S) 3 4 5 6 D I* [ 0.000000] ssb: core 0x0812, irq : 2(S) 3 4 5* 6 D I [ 0.000000] ssb: core 0x081c, irq : 2(S) 3 4 5 6 D I* [ 0.000000] ssb: Sonics Silicon Backplane found at address 0x18000000 [ 0.000000] Serial init done. [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 01000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x00ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x00ffffff] [ 0.000000] On node 0 totalpages: 4096 [ 0.000000] free_area_init_node: node 0, pgdat 802bc4c0, node_mem_map 80337000 [ 0.000000] Normal zone: 32 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 4064 pages, LIFO batch:0 [ 0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes. [ 0.000000] Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064 [ 0.000000] Kernel command line: noinitrd console=ttyS0,115200 oops=panic panic=10 [ 0.000000] PID hash table entries: 64 (order: -4, 256 bytes) [ 0.000000] Dentry cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Inode-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] Memory: 12892k/16384k available (2324k kernel code, 3492k reserved, 544k data, 196k init, 0k highmem) [ 0.000000] NR_IRQS:128 [ 0.000000] console [ttyS0] enabled [ 0.132000] Calibrating delay loop... 198.65 BogoMIPS (lpj=397312) [ 0.164000] pid_max: default: 32768 minimum: 301 [ 0.168000] Mount-cache hash table entries: 512 [ 0.180000] NET: Registered protocol family 16 [ 0.232000] bio: create slab at 0 [ 0.248000] Switching to clocksource MIPS [ 0.284000] NET: Registered protocol family 2 [ 0.292000] TCP established hash table entries: 512 (order: 0, 4096 bytes) [ 0.300000] TCP bind hash table entries: 512 (order: -1, 2048 bytes) [ 0.304000] TCP: Hash tables configured (established 512 bind 512) [ 0.312000] TCP: reno registered [ 0.316000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.324000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.332000] NET: Registered protocol family 1 [ 0.336000] PCI: CLS 0 bytes, default 16 [ 0.348000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.352000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.364000] msgmni has been set to 25 [ 0.368000] io scheduler noop registered [ 0.372000] io scheduler deadline registered (default) [ 0.380000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled [ 0.408000] serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a U6_16550A [ 0.436000] serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a U6_16550A [ 0.468000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a U6_16550A [ 0.496000] serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a U6_16550A [ 0.516000] physmap platform flash device: 02000001 at 1c000000 [ 0.520000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x00ddda Chip ID 0x00227e [ 0.532000] physmap-flash.0: Found an alias at 0x400000 for the chip at 0x0 [ 0.532000] physmap-flash.0: Found an alias at 0x800000 for the chip at 0x0 [ 0.532000] physmap-flash.0: Found an alias at 0xc00000 for the chip at 0x0 [ 0.532000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0 [ 0.532000] physmap-flash.0: Found an alias at 0x1400000 for the chip at 0x0 [ 0.532000] physmap-flash.0: Found an alias at 0x1800000 for the chip at 0x0 [ 0.532000] physmap-flash.0: Found an alias at 0x1c00000 for the chip at 0x0 [ 0.532000] Amd/Fujitsu Extended Query Table at 0x0040 [ 0.536000] Amd/Fujitsu Extended Query version 1.3. [ 0.544000] number of CFI chips: 1 [ 0.564000] 6 bcm47xxpart partitions found on MTD device physmap-flash.0 [ 0.572000] Creating 6 MTD partitions on "physmap-flash.0": [ 0.576000] 0x000000000000-0x000000040000 : "boot" [ 0.588000] 0x000000040000-0x0000003f0000 : "firmware" [ 0.600000] 0x00000004001c-0x000000040960 : "loader" [ 0.612000] 0x000000040960-0x00000013b000 : "linux" [ 0.620000] mtd: partition "linux" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.640000] 0x00000013b000-0x0000003f0000 : "rootfs" [ 0.644000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.664000] mtd: partition "rootfs" set to be root filesystem [ 0.672000] mtd: partition "rootfs_data" created automatically, ofs=300000, len=F0000 [ 0.680000] 0x000000300000-0x0000003f0000 : "rootfs_data" [ 0.692000] 0x0000003f0000-0x000000400000 : "nvram" [ 0.712000] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer) [ 0.724000] TCP: cubic registered [ 0.728000] NET: Registered protocol family 17 [ 0.732000] 8021q: 802.1Q VLAN Support v1.8 [ 0.756000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 0.764000] Freeing unused kernel memory: 196k freed [ 5.144000] Found board: "Buffalo WHR-HP-G54" [ 5.148000] diag: kernel found a "Buffalo WHR-HP-G54" [ 5.152000] diag: Detected 'Buffalo WHR-HP-G54' [ 5.636000] b44: Broadcom 44xx/47xx 10/100 PCI ethernet driver version 2.0 [ 5.672000] b44 ssb0:0 eth0: Broadcom 44xx/47xx 10/100 PCI ethernet driver 00:24:a5:42:71:12 [ 5.832000] b44 ssb0:0 eth0: Link is up at 100 Mbps, full duplex [ 5.840000] b44 ssb0:0 eth0: Flow control is off for TX and off for RX [ 5.956000] roboswitch: Probing device 'eth0' [ 5.964000] roboswitch: found a 5325! at eth0 [ 10.608000] jffs2: notice: (320) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 21 of xref (0 dead, 10 orphan) found. [ 28.112000] Compat-drivers backport release: compat-drivers-2013-01-21-1 [ 28.116000] Backport based on wireless-testing.git master-2013-02-22 [ 28.124000] compat.git: wireless-testing.git [ 28.220000] cfg80211: Calling CRDA to update world regulatory domain [ 28.224000] cfg80211: World regulatory domain updated: [ 28.232000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 28.240000] cfg80211: (2400000 KHz - 2494000 KHz @ 40000 KHz), (N/A, 3500 mBm) [ 28.248000] cfg80211: (4910000 KHz - 5895000 KHz @ 40000 KHz), (N/A, 3500 mBm) [ 29.184000] zsmalloc: module is from the staging directory, the quality is unknown, you have been warned. [ 29.236000] zram: module is from the staging directory, the quality is unknown, you have been warned. [ 29.248000] zram: num_devices not specified. Using default: 1 [ 29.256000] zram: Creating 1 devices ... [ 30.468000] b43-phy0: Broadcom 5352 WLAN found (core revision 9) [ 30.500000] b43-phy0: Found PHY: Analog 2, Type 2 (G), Revision 7 [ 30.528000] Broadcom 43xx driver loaded [ Features: PL ] [ 31.044000] ieee80211 phy0: Failed to initialize wep: -2 [ 31.044000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 31.352000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 31.880000] nf_conntrack version 0.5.0 (204 buckets, 816 max) [ 40.700000] b44 ssb0:0 eth0: powering down PHY [ 40.728000] b44 ssb0:0 eth0: Link is up at 100 Mbps, full duplex [ 40.736000] b44 ssb0:0 eth0: Flow control is off for TX and off for RX