[ 0.000000] Linux version 3.10.4 (bastian@gcc20) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2012.12 r37508) ) #2 Fri Aug 2 22:23:57 CEST 2013 [ 0.000000] MyLoader: sysp=4b1bf7b5, boardp=9002c600, parts=6bde8914 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0001974c (MIPS 74Kc) [ 0.000000] SoC: Atheros AR9344 rev 2 [ 0.000000] Clocks: CPU:560.000MHz, DDR:450.000MHz, AHB:225.000MHz, Ref:40.000MHz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x07ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x07ffffff] [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] free_area_init_node: node 0, pgdat 803069b0, node_mem_map 81000000 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: board=TL-WDR4300 oops=panic panic=10 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 126248k/131072k available (2208k kernel code, 4824k reserved, 592k data, 268k init, 0k highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.060000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688) [ 0.070000] pid_max: default: 32768 minimum: 301 [ 0.070000] Mount-cache hash table entries: 512 [ 0.080000] NET: Registered protocol family 16 [ 0.080000] MIPS: machine is TP-LINK TL-WDR3600/4300/4310 [ 0.090000] registering PCI controller with io_map_base unset [ 0.310000] bio: create slab at 0 [ 0.310000] PCI host bridge to bus 0000:00 [ 0.320000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff] [ 0.320000] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.330000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.330000] pci 0000:00:00.0: [168c:0033] type 00 class 0x028000 [ 0.330000] pci 0000:00:00.0: invalid calibration data [ 0.340000] pci 0000:00:00.0: reg 10: [mem 0x00000000-0x0001ffff 64bit] [ 0.340000] pci 0000:00:00.0: reg 30: [mem 0x00000000-0x0000ffff pref] [ 0.340000] pci 0000:00:00.0: supports D1 [ 0.340000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 0.340000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.340000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit] [ 0.340000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref] [ 0.350000] pci 0000:00:00.0: using irq 40 for pin 1 [ 0.350000] Switching to clocksource MIPS [ 0.360000] NET: Registered protocol family 2 [ 0.360000] TCP established hash table entries: 1024 (order: 1, 8192 bytes) [ 0.360000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.370000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.370000] TCP: reno registered [ 0.370000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.380000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.390000] NET: Registered protocol family 1 [ 0.390000] PCI: CLS 0 bytes, default 32 [ 0.400000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.410000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.420000] msgmni has been set to 246 [ 0.420000] io scheduler noop registered [ 0.430000] io scheduler deadline registered (default) [ 0.430000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.460000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A [ 0.470000] console [ttyS0] enabled, bootconsole disabled [ 0.480000] ath79-spi ath79-spi: master is unqueued, this is deprecated [ 0.490000] m25p80 spi0.0: found s25fl064k, expected m25p80 [ 0.490000] m25p80 spi0.0: s25fl064k (8192 Kbytes) [ 0.500000] 5 tp-link partitions found on MTD device spi0.0 [ 0.500000] Creating 5 MTD partitions on "spi0.0": [ 0.510000] 0x000000000000-0x000000020000 : "u-boot" [ 0.520000] 0x000000020000-0x000000119b4c : "kernel" [ 0.520000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.530000] 0x000000119b4c-0x0000007f0000 : "rootfs" [ 0.540000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.550000] mtd: partition "rootfs" set to be root filesystem [ 0.560000] mtd: partition "rootfs_data" created automatically, ofs=0x4a0000, len=0x350000 [ 0.570000] 0x0000004a0000-0x0000007f0000 : "rootfs_data" [ 0.580000] 0x0000007f0000-0x000000800000 : "art" [ 0.580000] 0x000000020000-0x0000007f0000 : "firmware" [ 0.620000] switch0: Atheros AR8327 rev. 2 switch registered on ag71xx-mdio.0 [ 1.850000] libphy: ag71xx_mdio: probed [ 1.860000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII [ 2.410000] ag71xx ag71xx.0 eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd033, driver=Atheros AR8216/AR8236/AR8316] [ 2.430000] TCP: cubic registered [ 2.430000] NET: Registered protocol family 17 [ 2.440000] 8021q: 802.1Q VLAN Support v1.8 [ 2.450000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 2.450000] Freeing unused kernel memory: 268K (8031d000 - 80360000) [ 4.260000] usbcore: registered new interface driver usbfs [ 4.260000] usbcore: registered new interface driver hub [ 4.270000] usbcore: registered new device driver usb [ 4.400000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.410000] ehci-platform: EHCI generic platform driver [ 4.420000] ehci-platform ehci-platform: EHCI Host Controller [ 4.420000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 4.430000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000 [ 4.460000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 [ 4.460000] hub 1-0:1.0: USB hub found [ 4.470000] hub 1-0:1.0: 1 port detected [ 4.550000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 4.820000] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 5.000000] hub 1-1:1.0: USB hub found [ 5.010000] hub 1-1:1.0: 4 ports detected [ 6.530000] eth0: link up (1000Mbps/Full duplex) [ 7.180000] jffs2: notice: (350) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 93 of xref (0 dead, 77 orphan) found. [ 7.210000] eth0: link down [ 8.330000] zram: Created 1 device(s) ... [ 9.400000] Adding 62460k swap on /dev/zram0. Priority:-1 extents:1 across:62460k SS [ 16.680000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5 [ 16.690000] Backport generated by backports.git backports-20130617-4-ge3220f5 [ 16.720000] cfg80211: Calling CRDA to update world regulatory domain [ 16.720000] cfg80211: World regulatory domain updated: [ 16.730000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 16.740000] cfg80211: (2400000 KHz - 2494000 KHz @ 40000 KHz), (N/A, 3000 mBm) [ 16.740000] cfg80211: (4910000 KHz - 5895000 KHz @ 40000 KHz), (N/A, 3000 mBm) [ 17.010000] NET: Registered protocol family 10 [ 17.490000] ath: EEPROM regdomain: 0x0 [ 17.490000] ath: EEPROM indicates default country code should be used [ 17.490000] ath: doing EEPROM country->regdmn map search [ 17.490000] ath: country maps to regdmn code: 0x3a [ 17.490000] ath: Country alpha2 being used: US [ 17.490000] ath: Regpair used: 0x3a [ 17.490000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 17.500000] cfg80211: Calling CRDA for country: US [ 17.500000] cfg80211: Regulatory domain changed to country: US [ 17.510000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 17.520000] cfg80211: (2400000 KHz - 2494000 KHz @ 40000 KHz), (N/A, 3000 mBm) [ 17.530000] cfg80211: (4910000 KHz - 5895000 KHz @ 40000 KHz), (N/A, 3000 mBm) [ 17.530000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47 [ 17.540000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 17.550000] ath: EEPROM regdomain: 0x0 [ 17.550000] ath: EEPROM indicates default country code should be used [ 17.550000] ath: doing EEPROM country->regdmn map search [ 17.550000] ath: country maps to regdmn code: 0x3a [ 17.550000] ath: Country alpha2 being used: US [ 17.550000] ath: Regpair used: 0x3a [ 17.570000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht' [ 17.570000] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40 [ 17.800000] PPP generic driver version 2.4.2 [ 17.820000] tun: Universal TUN/TAP device driver, 1.6 [ 17.820000] tun: (C) 1999-2004 Max Krasnyansky [ 18.070000] ipip: IPv4 over IPv4 tunneling driver [ 18.340000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 18.370000] xt_time: kernel timezone is -0000 [ 18.530000] NET: Registered protocol family 24 [ 18.540000] nf_conntrack version 0.5.0 (1976 buckets, 7904 max) [ 19.400000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 19.490000] batman_adv: B.A.T.M.A.N. advanced 2013.2.0 (compatibility version 14) loaded [ 19.740000] u32 classifier [ 19.750000] input device check on [ 19.750000] Actions configured [ 19.860000] Mirror/redirect action on [ 20.010000] Failed to load ipt action [ 23.560000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 23.570000] device eth0 entered promiscuous mode [ 23.570000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready [ 23.580000] eth0: link up (1000Mbps/Full duplex) [ 23.590000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 23.590000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready [ 23.900000] batman_adv: bat0: Adding interface: eth0.1 [ 23.900000] batman_adv: bat0: The MTU of interface eth0.1 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1528 would solve the problem. [ 23.930000] batman_adv: bat0: Interface activated: eth0.1 [ 23.940000] device bat0 entered promiscuous mode [ 23.950000] batman_adv: bat0: Adding interface: eth0.2 [ 23.950000] batman_adv: bat0: The MTU of interface eth0.2 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1528 would solve the problem. [ 23.980000] batman_adv: bat0: Interface activated: eth0.2 [ 24.000000] br-mybridge: port 1(bat0) entered forwarding state [ 24.000000] br-mybridge: port 1(bat0) entered forwarding state [ 24.590000] batman_adv: bat0: bridge_loop_avoidance: Changing from: disabled to: enabled [ 24.610000] batman_adv: bat0: Changing gateway bandwidth from: '41' to: '31' (propagating: 512KBit/512KBit) [ 24.620000] batman_adv: bat0: Changing gw mode from: off to: server [ 26.000000] br-mybridge: port 1(bat0) entered forwarding state [ 30.100000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 30.140000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 30.150000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 33.150000] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready [ 34.580000] batman_adv: bat0: Adding interface: wlan0-1 [ 34.590000] batman_adv: bat0: The MTU of interface wlan0-1 is too small (1500) to handle the transport of batman-adv packets. Packets going over this interface will be fragmented on layer2 which could impact the performance. Setting the MTU to 1528 would solve the problem. [ 34.610000] batman_adv: bat0: Interface activated: wlan0-1 [ 36.660000] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready [ 36.680000] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready [ 36.700000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready [ 39.960000] IPv6: ADDRCONF(NETDEV_UP): wlan1-1: link is not ready [ 40.110000] wlan1-1: Selected IBSS BSSID 02:ca:ff:ee:00:36 based on configured SSID [ 40.120000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1-1: link becomes ready [ 40.190000] wlan0-1: Creating new IBSS network, BSSID 02:ca:ff:ee:00:11 [ 40.190000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready [ 49.670000] HTB: quantum of class 10001 is big. Consider r2q change. [ 50.820000] HTB: quantum of class 10003 is big. Consider r2q change. [ 51.980000] HTB: quantum of class 10005 is big. Consider r2q change. [ 176.570000] HTB: quantum of class 10007 is big. Consider r2q change. [ 213.860000] device wlan0 entered promiscuous mode [ 213.860000] br-mybridge: port 2(wlan0) entered forwarding state [ 213.870000] br-mybridge: port 2(wlan0) entered forwarding state [ 215.870000] br-mybridge: port 2(wlan0) entered forwarding state [21237.770000] HTB: quantum of class 10001 is big. Consider r2q change. [21523.090000] HTB: quantum of class 10003 is big. Consider r2q change. [31893.190000] HTB: quantum of class 10005 is big. Consider r2q change. [38656.730000] net_ratelimit: 60 callbacks suppressed [38898.120000] net_ratelimit: 149 callbacks suppressed [40295.020000] net_ratelimit: 17 callbacks suppressed [46396.920000] HTB: quantum of class 10007 is big. Consider r2q change.