[   33.240000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   33.260000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   33.280000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   68.880000] device wlan0 entered promiscuous mode
[   68.890000] br-mybridge: port 2(wlan0) entered forwarding state
[   68.900000] br-mybridge: port 2(wlan0) entered forwarding state
[   68.980000] device br-mybridge entered promiscuous mode
[   70.900000] br-mybridge: port 2(wlan0) entered forwarding state
EG-labor-AP
up: 79.88 load: 0.43 rest: 0.16 0.06 2/39 3118
procd: - init complete -
EG-labor-AP
up: 199.88 load: 0.26 rest: 0.20 0.08 2/36 4061
EG-labor-AP
up: 259.88 load: 0.20 rest: 0.19 0.09 2/38 4241
EG-labor-AP
up: 319.89 load: 0.15 rest: 0.17 0.09 2/36 4404
EG-labor-AP
up: 380.15 load: 0.19 rest: 0.20 0.10 3/37 4883
EG-labor-AP
up: 499.89 load: 0.13 rest: 0.22 0.13 2/38 7091
EG-labor-AP
up: 575.89 load: 0.22 rest: 0.26 0.15 2/37 7252
EG-labor-AP
up: 635.89 load: 0.21 rest: 0.27 0.16 2/36 7425
EG-labor-AP
up: 695.90 load: 0.14 rest: 0.25 0.16 2/37 7582
EG-labor-AP
up: 755.90 load: 0.08 rest: 0.22 0.15 2/37 7740
EG-labor-AP
up: 815.90 load: 0.06 rest: 0.19 0.15 2/37 7898
EG-labor-AP
up: 875.90 load: 0.05 rest: 0.17 0.14 2/37 8056
EG-labor-AP
up: 935.90 load: 0.05 rest: 0.15 0.14 2/37 8214
[  951.340000] ath: phy0: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x000084c0
[  951.350000] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
EG-labor-AP
up: 995.90 load: 0.22 rest: 0.18 0.15 2/36 8372
[ 1095.860000] ath: phy0: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x000286c0
[ 1095.870000] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 1097.840000] ath: phy0: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x000286c0
[ 1097.850000] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 1098.700000] ath: phy0: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x000286c0
[ 1098.710000] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
EG-labor-AP
up: 1116.65 load: 0.31 rest: 0.29 0.19 2/38 9759
[ 1121.380000] ath: phy0: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x000286c0
[ 1121.390000] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
[ 1137.910000] ath: phy0: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x000084c0
[ 1137.920000] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
EG-labor-AP
up: 1175.69 load: 0.15 rest: 0.25 0.19 2/38 9959
EG-labor-AP
up: 1237.69 load: 1.92 rest: 0.85 0.41 3/38 10158
[ 1239.310000] ath: phy0: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x000084c0
[ 1239.320000] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
�

U-Boot 1.1.4 (Nov 17 2009 - 11:56:26)

AP83 (ar9100) U-boot 0.0.11
DRAM:
sri
32 MB
id read 0x100000ff
flash size 8MB, sector count = 128